View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. vector. System/Component overview. Lenze. FU vector en 11/ 3. System overview/Selection guide. Communication modules e.g. keypad or. PROFIBUS. Get Lenze IB Manual. Get all Lenze manuals! with optical fibre cable together with the controller series as of E DC controller E 5x. 6x.

Author:	Jujora Taujin
Country:	India
Language:	English (Spanish)
Genre:	Sex
Published (Last):	3 May 2017
Pages:	425
PDF File Size:	3.24 Mb
ePub File Size:	6.71 Mb
ISBN:	358-7-12567-166-5
Downloads:	50688
Price:	Free* [*Free Regsitration Required]
Uploader:	Samuktilar

To print the manual completely, please, download it.

Setting Of The Torque Controller Automation status word 58C4hex Data format: These Operating Instructions give advice and recommendations for the installation manial use of the electronic equipment. Position control WP.

Lenze IB : Manual

Page 70 Byte assignment of the process data If a word parameter 16 bit is assigned to the process data, the parameter address index, subindex is entered in the first corresponding byte. The IB bus interface module has the following features: When manuaal the operating mode, also the operating unit or one of the LECOM interfaces are available.

Selection Of The Configuration The setting of CO05 determines which input channels and which controls will be activated: Lebze the adjustment of the act. Tell us about it.

Programming The programming section using the IB bus interface module is divided into the following chapters: Page 87 Enabling JOG frequencies With terminal control activate the assigned digital inputs according to the table below. Setting Of The Pid Controller 9. The controller is inhibited and waits for controller enable. It then switches manua, to the state “switch-on disabled”.

LSB Transmission of one bit. The brake contact which is switched in the event of overtemperature is designed for: With terminal control you tan read setpoint 1 under code Lwnze Connecting Module lb- Profibus Cable protecting fuses for recommended – 03 Controller type Rated fuse current 2 0 A 3 5 A 5 0 A 16 mm2 Cable Cross-sectlon 4 mm2 6 6 1 2 6 6 1 4 8 6 1 5 Controller type 6 3 A A For cyclic overload, the ratio overload to cycle time must not exceed 0.

Ratings Of Rfi Filters Integral Action Component If the mounting plates are painted, the paint must be removed in every case. Planning Planning Features of the series variant dancer-Position control In addition to numerous Standard functions, this variant offers various functions which are required for a dancer-Position control used for winding applications.

Analog Inputs And Outputs DP parameter setting channel For the DP parameter setting channel, parameter setting and diagnosis is possible in the user data operation.

Lenze | DACPOL SERVICE

Technical Data Of Sine Filters 6. Manufacturer’s Declaration We hereby certify that the electronic controllers listed in these ,enze Instructions are control components for variable speed motors intended to be assembled into machines or to form a machine together with other components. Technical Data Of Mains Chokes The arrow Position marks whether you are in the code or in the Parameter level.

The data structure is the same for input and output data, see following tables.

The controller has an automatic baud rate recognition see L-C Minimum Field Frequency Fdmin Controller inhibit Fault indication TRIP If you need the permanently assigned output terminal 45 with the polarity as required. Digital Inputs And Outputs The lower the max. msnual

LENZE SERIES OPERATING INSTRUCTIONS MANUAL Pdf Download.

Checking the power Stage The measurements described below are to be carried out only by indicate the nominal value. Ramp Generator Stop The controller divides the Speed setpoint by the actual winding diameter.

To switch the Signal cables, only use relays with low- current contacts.

Closed-loop Speed Control The large setting ranges of the control Parameters also allow the control of an application datum if this depends on the drive Speed. For mwnual explanations of the Codes and their possible functions refer to the corresponding chapters.

Table Of Contents When using several mounting plates they must be connected with as large surface as possible e-g.

Wiring Power connections cabinet All power terminals remain live up to 3 minutes after mains disconnection! Page 46 The parameter communication with the controller has the following sequence: Installation In Compliance With Emc FMS process data Process data are data memories where several individual parameters are combined to form a new parameter, the manuak data.

If you want to set the controller locally, proceed just like in the operating mode mixed operation. Unsigned16 with 4 elements Process data are data memories where several individual parameters are combined to form a new parameter, the process data.

Signal Of The Ultrasonic Sensor: For master-Slave couplings it is important that, in case of Speed A frequency Signal which is proportional to the field frequency tan be supplied to terminal X9.