JIS G Hot-rolled high strength steel plate, sheet and strip with improved formability for automobile structural uses (FOREIGN. JIS G Hot-rolled high strength steel plates, sheet and strip with improved formability for automobile uses. Find the most up-to-date version of JIS G at Engineering
|Country:||Antigua & Barbuda|
|Published (Last):||25 February 2011|
|PDF File Size:||10.25 Mb|
|ePub File Size:||15.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
This steel is widely used in floor applications, prevent skidding applications and fast drain water applications. Contact us Details Category: Usually delivered with rust-preventive oil on it. For Si content, the following ranges and limits may be specified.
Mechanical properties Thickness mm 1. High skid resistance 2.
In such case B50 is not used for guarantee. Analyst Contact Analyst Report. Those steels which have not been annealed shall be subjected to annealing according to the previous table and subsequently quenching and tempering.
BS part 1 EN: Special elements other than those shown in the table are added. Measuring point of thickness shall be any point not less than 20 y3134 from a side edge.
SPHT-1, 2, 3, 4. In case of the steel made by electric arc furnace, specified range of those elements, C, Mn, Cr, shall be c. This steel, which has high-strength qualities and good formability, is used in high-pressure gas containers, with less than a litres inner capacity, used for holding LPG, acetylene, and other high-pressure gases. Thickness tolerance is subject to the tables below. As for the Charpy absorption energy, the values higher than those in the table may be agreed upon by the parties concerned.
Download Now White Paper: Standard thickness except should preferably be used. Analyst Contact Analyst Report. The Eng-Tips staff will check this out and take appropriate action. Chemical nis and appropriate conditions to apply NAC-2 Series. This steel is widely used in general fabrication purposes, drawing, general pipes, structural pipes, galvanized steel pipes, and cold rolled steel.
Spf 60 Import Data in June –
Another table shall be applied to steel sheet less than mm in width. Specification of hot-rolled steel for cold rolling mill depends upon each manufacturer’s requirement. Please consult with us on this matter. But level of air pollution,fluctuation of climatic conditions and many other factors may cause some difference in the corrosion resistant effects even if the material is the same quality. Flatness shall, as a rule, be measured by placing a steel sheet on a flat surface plate and the value of flatness shall be determined as the difference between the maximum deviation of the uppermost surface on the convex side and the thickness of the steel sheet.
SPFH (JIS ) – Worldwide equivalent grades
Tighter tolerances are available, please contact us. NAC-2 Corrosion resistant hot rolled steel sheet This steel is comparable to SS grade but added with special elements to impart excellent corrosion resistance to sulfuric and hydrochloric acid. BS part 1 EN: By joining you are opting in to receive e-mail. Good formability and weldability 3. Other features are superiority in mass reduction, atmospheric corrosion resistance, weldability, formability and appropriate level of strength.
For thickness tolerance Table in the right is applied.
Thickness tolerance shall be subject to JIS G G313 rolled mild steel plates, sheets and strip Corrosion resistant hot rolled steel sheet for forming, corrosion resistant hot rolled steel sheet with high flange-stretchability are also available. Very rare occurrence gg3134 distortion or blister during firing 4. We have helped many customers convert successfully to iis steels.
The value specified in the above table shall be applied to any length of mm, and in the case of the 3. Paintability and paint adhesion are also excellent Applicable specifications Shot blast steel plates shall be produced in conformity to any specifications such as JIS Standard, shipbuilding standard, overseas standard and NKK Standard. Proper painting or surface treatment will further enhance the performance of this atmospheric corrosion resistant steel.
Details of Spf 60 Import Data in June
Please contact us for further information on Charpy toughness and impact test properties. Related products Hot-rolled – Advanced and ultra high-strength steel Hot-rolled – Steel for forming Direct-rolled – High-strength steel Cold-rolled – High-strength steel Metallic coated – High-strength steel.
Therefore this steel is most appropriate structural steel for harbor, wharf and other marine structures. Can it be cross referenced to something else. Connect with us We’re on Social Networks. This email address is being protected from spambots.