ISO 16047 PDF

according to test requirements such as BS Pt. 2 or ISO This can be expressed in two ways, the Coefficient of Friction µ and the Torque Coefficient (K . ISO FASTENERS – TORQUE/CLAMP FORCE TESTING. DIN EN ISO Fasteners – Torque/clamp force testing (ISO + Amd ) (includes Amendment).

Author: Yogrel Nigul
Country: Bhutan
Language: English (Spanish)
Genre: Technology
Published (Last): 13 November 2016
Pages: 221
PDF File Size: 15.24 Mb
ePub File Size: 13.86 Mb
ISBN: 737-6-85290-331-8
Downloads: 7009
Price: Free* [*Free Regsitration Required]
Uploader: Nigal

Eddy current method phase sensitive. You may delete a document from your Alert Profile at any time. This will give you increased confidence in your fastener designs and manufacturing processes. If they are fastened too tightly, components and the fasteners themselves may be damaged. Username or email address: This ensures that you are always up-to-date and saves you both time and money. Uncoated reference parts are oiled to protect against corrosion and later cleaned again. Subscription pricing is determined by: These are then tightened with the same torque, although the coefficient of friction of the fasteners with captive washers is lower.

The option of choosing between uncoated and galvanised bases reflects the prevailing procedures in the American and European areas. Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

With these fasteners a washer is threaded onto the blank; the subsequent cold forming in which the thread is rolled into the surface ensures that this washer cannot fall off. MEC can be perform tests on actual fastened assemblies to obtain torque-angle graphs and to establish the torque to reach the yield strength of the bolt.

TOP Related  GARMISCH PARTENKIRCHEN STADTPLAN PDF

If you need to be able to add standards to the monitoring service, you must register as a user with your own username and password. Coefficients of friction cannot be specified using measurement technology. Start Webshop Product catalog Product presentation.

Product Validation, Verification and Testing

Please first log in with a verified email before subscribing to alerts. Please first verify your email before subscribing to alerts. These are useful, for example in comparing the coefficients of friction of different coating systems. Pressure water jetting test. There are many types of engineering simulation and analyses that Matrix Engineering Consultants performs either as a stand-alone service or integrated into our projects.

When tightening the bolt the clamp force, the rotation angle, the total torque and one of the two partial torques are measured.

BS EN ISO 16047:2005+A1:2012

We have capability to collect time synchronized data across multiple instruments and sensors including the following:. The respective complementary partial torque can be identified via subtraction.

Surfaces often have a major influence on this. Every day, thousands upon thousands of screws and bolts are used to fasten components together. In this process the fasteners are screwed to their own washer.

ISO 16047:2005

Electrostatic powder spraying EPS. The relationship between input torque and induced tension in a specific fastener application can be determined by testing the fastener with a calibrated load cell and torque device. When fastening, the torque must be correct in order to achieve the required clamp force — the force that a fastener uses to hold two components together. This technique has a distinct advantage because the actual joint and fastener can be tested without compromising the joint stiffness through the introduction of a load cell.

TOP Related  LIDERAZGO SIN LIMITES RONALD HEIFETZ PDF

These bases may be of low or high hardness, uncoated or galvanised. On some test benches the partial torque is measured in the thread, in others on the base. For example, brighteners in the galvanised coat serve to lower the friction between reference part and fastener. Such data can be used to establish the appropriate torque-angle requirement for the specific fastener and joint.

Have fun clicking through!

The testing of fasteners with captive washers is not described in the standard. Technical terms can not always be avoided. The objective is to fix components to each other in a way that enables them to fulfil their function.

Webprint Printed and bound. They can also be used to cover larger holes.

Tightening specifications for normal fasteners are also applied for those with washers. A bolt that requires testing is screwed into the test bench and fixed with a reference bolt. The bolt heads lie on a reference base plate or a reference washer. If the factor is very high, fasteners need to be tightened with a high torque and the efficiency of the fasteners decreases.

Industrial companies and associations often specify a coefficient of friction window for this. Coefficients of friction calculated according to ISO standard need to be regarded with caution, however. Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.