Provides information to enable POS operators to use the TM-. L90 safely and correctly. TM-L90 Service Manual. Describes maintenance, inspection and repair . EPSON has been taking industryinitiatives with its own POS printer . TM-L90 with Peeler User’s Manual TM-L90 peeler specification safely and correctly. Epson TM-L90 is a label printer for retail printing with receipt and greyscale printing. It also has greyscale for multi-tone printing.
|Published (Last):||24 November 2006|
|PDF File Size:||9.20 Mb|
|ePub File Size:||20.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
When removing it, do not pull forcibly, as this may result in deformation. Once the printer is used, do not change the cutting method from partial cut to full cut, because of the difference in the wear rate on the blades between the areas where the paper passes and the paper does not pass, which can result in a paper-cutting problem. Confidential Horizontal Installation Place the printer with the paper exit facing mqnual.
Do not place the printer in an unstable place such as on an unsteady base or on a slanted surface. When installing, route the cutter lead wire as shown below, and then fix with the insulating tape. Product may break eppson cause injury if it falls. Then close the paper roll cover.
Log in Not signed in yet? Slide out the paper feed motor from the hole in the frame L assembly. Be sure to set this equipment on a firm, stable, flat surface.
Remove the epxon wire of the BM black mark t-l90 set board from the hooks epsin the platen holder. Linux Mac OS 7. When assembling, make sure you manuao the spacers in the direction shown below. Not yet an Epson partner? Roll paper cover Main case assembly Cutter cover Install in the reverse sequence of removal. Remove the paper cutter cover assembly.
Adjusting screw Fixed position 1 diameter: Avoid using alcohol, benzene, thinner, trichloroethylene, or ketone-based substances to remove dirt or foreign matter from the printer, because these substances can affect or damage plastic and rubber parts.
To select partial cut: Remove two S1 screws and one S2 screw. Users may choose between partial cut and full cut by adjusting the autocutter unit to the desired position. Larger receipt rolls, wider paper Altogether, the TM-L90 label printer is one of the most efficient label printers available: Remove one S1 screw to release the ground wire of the BM paper detector circuit board assembly. Do not damage the thermal head by touching it with your fingers or any hard object.
Do not touch the thermal head or radiation plate. Register The fields marked with an asterisk are required fields.
Test Points On Epsno Printer Mechanism Confidential Test Points on the Printer Mechanism Before you replace the main circuit board to see if the printer is repaired, you need to check the printer mechanism.
C Disassembly and Assembly Note that the new head has a spacer on it.
TM-L90 User’s Manual (14 Languages) – Thermal line Printer – Download – POS – Epson
Install the printer in a location, such as at the edge of a counter, where the backing paper will not accumulate near the paper exit. Confidential How to Use the Self-test There are two types of self-tests. Then turn it on again. It forms the nucleus of the control system for the TM-L If you use the cover operation label included in the package, attach it in one of the following locations: Remove the DIP switch cover mnual the hinge cover.
Tech Specs Product features and specifications are subject to change without prior notice. Remove one switch screw and remove the cover detector assembly from frame R. Disconnect the power cord from the wall outlet before doing this.
Confidential Hinge Cover 1. Register now We respect your privacy. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Vertical installation Horizontal installation 5. Has been successfully added to your basket Continue shopping Go to checkout. With the main assembly upside ,anual, remove two S6 screws. You can unsubscribe at any time with a click on the link provided in every Epson newsletter.
Epson TM-L90 series Service Manual
Push the label paper spacer until you feel it click onto the shaft. Page 75 Confidential Note: B viii Add the information of the related documentation Reason for change: Page 11 Do not block the label peeler detector with your fingers, or anything else while the label issuing is in progress. Disengage both projections located in the lower part of the auxiliary holder plate, and pull out the auxiliary holder plate downward, at an angle.
Make sure the two dowels on the frame assembly engage the two slits in the autocutter unit. Slide the label paper spacer to the appropriate width.
Then, pull the lead wire of the BM paper detector circuit board assembly out through the clearance in the hinge cover.