BERETTA AL391 URIKA MANUAL PDF

Owner’s Manuals. Below, you may find manuals for your Beretta firearm in an electronic format. You may also order a hard copy if desired. Owner’s Manuals. Unofficial Beretta Site: really neat site, complete with the history of the model 92 series, old ‘owner’s manual, exploded views, 70 (Thanks to Ed Ruesing, he gave me the opportunity to post the manual) KB, English AL ( KB). The illustrations and instructions in this article are based on the Beretta Urika , but they are also valid for the other versions of the

Author: Malagor Duktilar
Country: Bhutan
Language: English (Spanish)
Genre: Environment
Published (Last): 6 December 2006
Pages: 203
PDF File Size: 10.83 Mb
ePub File Size: 20.90 Mb
ISBN: 682-2-20735-753-4
Downloads: 52136
Price: Free* [*Free Regsitration Required]
Uploader: Gajinn

In addition to the Basic Safety Rules, there are other Safety Rules pertaining to the loading, unloading, disassembly, assembly and use of this firearm located throughout this manual. Some of the guides are longer than the one illustrated – a design change, apparently.

Beretta AL391 Teknys Gold Target Owner Manual (Spanish)

Once you work the ring part way up, you urka grab it with thin-nosed pliers and pull it on out. Even if the gun is stored with the barrel on, the forend nut should be removed often, cleaned, and greased I recommend Anti-seize, but any lubricant is better than none to keep it from rusting and freezing in place.

This article does not apply at all to the Beretta gas-operated guns that have the recoil spring in the forearm a391 Lark series and the current Xtrema nor to Beretta’s recoil-operated shotguns ES Pintail or Victoria.

It is your responsibility to insure that children under the age of 18 or other unautho- rized persons do not gain access to your firearm. Breetta piston part 48 normally remains on the magazine cap shaft part 45but if the gun is dirty it may stick inside the gas cylinder on the barrel.

Some bullets can travel over a mile. Unscrew the forend nut Beretta’s name for it is forend cap part 55pull the forearm off, urioa pull the barrel off. Use a dentist’s pick or something similar to hook under the bottom edge of the ring, pull up a little, and work your way around pulling up just a tiny bit each time. To remove or replace the plug, pull the clip off and throw it away. The gas ports are two holes in the bottom of the barrel that feed gas from inside the barrel into the gas cylinder which is welded to the bottom of the barrel.

TOP Related  KOSMOS NOETOS PDF

When I did the cleaning with a thinner wire I had trouble with failures to eject, because the ports were open to some extent, but too narrow.

Beretta Web.com – Unofficial Beretta Site

Take care not to lose the plunger and its spring. It is possible to increase the magazine capacity from two to three rounds in the coun- tries where it is allowed. Any recommendations berrtta tools to quickly remove and replace the two nuts in the exhaust pressure relief valve for cleaning?

At this point, the trigger pin is likely to fall out, but that is OK, just don’t let it get lost. Stock drop and cast modification must be carried out by a compe- tent gunsmith.

Search the history of over billion web pages on the Internet. To see if the nut is still working properly, place it on a hard surface like a table top, with the spring-loaded part I will call it the plunger for lack of a better name down, and press on the top of the nut with the heel of your hand.

Do not store firearms in places which are or could be accessible by children or other persons whose unfamiliarity with firearms might lead to unsafe use.

U r i k a – Beretta AL Urika – Bev Fitchett’s Guns Magazine

The front end of the second shell will hang up on the right edge of the chamber, and not enter the chamber at all. It will be easier after the first time, because you probably won’t get it back on as tight as the factory did. It will work either way well, you berrtta that, if you have been putting it in the other way.

TOP Related  HEVAJRA TANTRA TEXT PDF

Please urikaa that devices intended to prevent accidents – for example, cable locks, chamber plugs, etc, – may not prevent use or misuse of your firearm bereetta a determined person. Replacing the recoil spring: So why didn’t Beretta switch to a rust-resistant steel for the outer part of the nut and leave the ring out? You should now be able to work the bolt up and down, compressing the recoil spring, by holding onto the operating rod.

Just remove it from the magazine cap often, flush the threads out with a solvent Gunscrubber, brake parts cleaner, Breakfree CLP, etc and lubricate it. I don’t, and I don’t think most shooters do, but I had a cap come loose one time, letting the stock get loose. To remove the carrier, just drive out the carrier pin, and make sure the small parts two round swivel joints, spring and spring guide don’t get lost when it all comes apart. The safety can be engaged only when the hammer is cocked.

This helped me alot when I wanted to remove the magazine plug. The result is that the shotgun, without any adjustment, fires everything from the light 24 gr. Older forend nuts do not have the mysterious ring, confirming that it was part of a design change, and that is why it does not show up on the parts diagram. It is common for clay shooters to remove the safeties from guns that are dedicated to clay shooting only.