ASTM F2413 05 PDF

1 | Page. ASTM. American Society For Testing and Materials. F Standard Specification for Performance Requirements for Foot. Protection. Abstract. Learn about ASTM footwear standards and how to properly read a label. The 11 after the dash signifies the footwear meets the ASTM F or F ASTM F EH Overshoes are made from yellow ozone resistant rubber that’s % waterproof.

Author: Muktilar Shakticage
Country: Ecuador
Language: English (Spanish)
Genre: Love
Published (Last): 13 August 2006
Pages: 313
PDF File Size: 3.42 Mb
ePub File Size: 4.77 Mb
ISBN: 168-3-70772-714-6
Downloads: 50163
Price: Free* [*Free Regsitration Required]
Uploader: Dazragore

The final rule went into effect in October A work boot that meets the impact and compression requirements of the ANSI standard may not provide protection for metatarsal, electrical or penetration hazards.

The puncture resistant device must be f24113 integral part of the footwear and must be constructed into the shoe during the manufacturing process. Lines 3 and 4 are used to reference additional sections in the standard.

ASTM F – 05 Standard Specification for Performance Requirements for Foot Protection

It also identifies the existence of impact resistance Ithe impact resistance rating 75 or 50 foot-poundscompression resistance C and the compression resistance rating 75 or 50 which correlates to pounds and pounds of compression respectively. The device must show ast sign of corrosion after being exposed to a five percent salt solution for hours. It also identifies the existence of impact resistance Ithe impact resistance rating 75, 50 or 30 foot-poundscompression resistance Cand the compression resistance rating 75, 50, or 30, which correlate to pounds, pounds, and pounds of compression respectively.

Dielectric insulation DI footwear is designed to provide additional aastm if accidental contact is made with energized electrical conductors, apparatus or circuits. It must be capable of withstanding the awtm of 18, volts at 60 hertz for one minute with no current flow or leakage current in excess of one milliampere under dry conditions.

TOP Related  HIKAYAT RAJA BABI PDF

It is intended to protect the foot area between the toe and lower leg. Footwear conforming to this specification shall meet the performance requirements for the following: Cancel reply Enter your comment here Notify me of new posts via email.

Asm how your comment data is processed. Static dissipative SD footwear is designed to reduce the accumulation of excess static electricity by conducting body charge to ground while maintaining a sufficiently high level of resistance. The puncture-resistant footwear must show no signs of cracking after being subjected to 1. Occupational Foot Protection According to The footwear must have a lower limit of electrical resistance of ohms and an upper limit of ohms. Add-On Devices An important point to remember is that neither the ANSI nor ASTM standards allows for the use of add-on type devices — strap-on foot, toe or metatarsal guards — as a substitute for protective footwear.

ASTM F2413-05 EH Footwear Overshoes

It indicates that the protective footwear meets the performance requirements of ASTM F, issued in Protective footwear can meet all the requirements ast the ANSI standard or specific elements of it, as long as it first meets the requirements for toe protection in Section 1.

The footwear must have a lower limit of electrical resistance of 10 6 ohms and an upper limit of 10 8 ohms. Most manufacturers of add-on devices have submitted their products to independent laboratories for testing.

They are use to designate metatarsal Mt resistance and rating, conductive Cd properties, electrical hazard EHpuncture resistance PR and static dissipative SD properties, if applicable. It must be capable of withstanding the application of 14, volts at 60 hertz for one minute with no current flow or leakage current in excess of 3.

TOP Related  BIOPHYSICS BIALEK PDF

Notify me of new comments via email. Standard specification astn performance requirements for protective safety toecap footwear. It is designed to dissipate state electricity from the body to the ground.

The outsole is intended to provide a secondary source of electric shock resistance protection to the wearer against the awtm from an incidental contact with live electrical circuits, electrically energized conductors, parts or apparatus.

Published by Jack Benton.

This line identifies the ANSI standard. This line identifies the gender [M Male or F Female ] of the user.

ASTM F EH Footwear Overshoes

One shoe of each pair must be clearly and legibly marked e. This specification covers the minimum design, performance, testing, and classification requirements, and prescribes fit, function, and performance criteria for footwear designed to protect against a variety of workplace hazards.

It is not the intention of 005 specification to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.

The marking must be enclosed in a rectangular border; a four-line format is recommended. Static dissipative SD footwear is designed to provide protection against hazards that may exist due to excessively low footwear resistance, as well as maintain a sufficiently high level of resistance to reduce the possibility of electric shock.

The footwear must facilitate electrical conductivity and the transfer of static electricity build up from the body to the ground.