FRENIC LIFT MANUAL PDF

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Vule Faulmaran
Country: Sierra Leone
Language: English (Spanish)
Genre: Literature
Published (Last): 28 January 2012
Pages: 238
PDF File Size: 14.9 Mb
ePub File Size: 6.8 Mb
ISBN: 415-3-89696-475-1
Downloads: 89698
Price: Free* [*Free Regsitration Required]
Uploader: Fegal

Removing the cable guide plate Before to proceed, remove the terminal block cover as shown below left.

Page 35 Table 2. Push the front cover against the case of the inverter and slide it upward until ffrenic latch at its top engages with the case. Consult your Fuji Electric representative if these terminals are to be used. Designed for Elevating Machinery. Last digit of year If you suspect the product is not working properly or if you have any questions about your product, contact your Fuji Electric representative.

Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other frsnic Page Immediately trip with alarm processing 1: The first letter is an alphabet that identifies its group and the following two letters are numerals that identify each individual code in the group.

Name of option Function and application Insert an MC in the power source side of the inverter in order to: For the braking resistor built-in type, refer to llift next page.

Chapter 6 Troubleshooting 1 First, check that the inverter is correctly wired, referring to Chapter 2, Section 2. Tuning offset angle of the magnet pole Before to proceed to running a synchronous motor, be sure to tune offset angle of the magnet pole. Page 61 L codes: To improve cooling efficiently, you can take the heat sink out of the equipment or the enclosure as shown on the right so frrenic cooling is done both internally and externally this is called “external cooling”.

TOP Related  AGILENT GENESYS TUTORIAL PDF

Check that a mechanical brake is in effect.

FRENIC-Lift | Fuji Electric Global

Otherwise, the inverter may be broken if you turn the power ON. How This Manual Is Organized This chapter lists specifications including output ratings, frenoc system, external dimensions and protective functions. Don’t show me this message again. Page 19 3 Lifg direction Horizontal layout is recommended when two or more inverters are to be installed in an equipment or enclosure.

Possible Causes What to Check and Suggested Measures 1 A high intensity noise was Check if appropriate noise control measures have been implemented e. Set up L02 for correct data. If any problems persist after the above recovery procedure, contact your Fuji Electric representative. Put the front cover back in reverse order of.

Please do not use it with other products. Possible Causes What to Check and Suggested Measures 1 Conditions for Compare the settings of the y manuual y01 to y10 with those of the host communications differ equipment.

Fuji Electric FRENIC-Lift series Instruction Manual

Page 77 [ 16 ] Run operation error Problem You incorrectly operated the inverter. Retry during the period specified by timer y Lower the mnaual around the motor. A dielectric strength test will cause breakage of the inverter similarly to the Megger test if the test procedure is wrong.

By pressing ‘print’ button you will print only current page. If any of these conditions has occurred, either eliminate the abnormal or error factor s manyal perform tuning again, or contact your Fuji Electric representative. Maximum speed F03 2 The reference torque bias follows the input voltage level on terminal [12].

TOP Related  CHANGEMAN TOOL IN MAINFRAME PDF

Doing so could cause frenlc. Page 48 Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using a multi-function keypad option.

On the bottom are no case fixing screws. Precautions For Use Precautions for use Driving a V When manjal a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur.

Manuaal the procedure below for wiring and configuration of the inverter. Init ialize all function code data to t he factory defaults H04 Auto-resetting 0: Page 31 These are provided for the DC link bus powered system.

When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally. FRENIC-Lift is an inverter designed to drive a three-phase induction motor hereafter called an induction motor and a three-phase permanent magnet synchronous motor hereafter called a synchronous motor for exclusively controlling elevating machinery.

To print the manual completely, please, download it. In the torque control, data of some function codes related to the control may be enabled or disabled. Frrnic two terminals prepared for grounding, which are indicated by the symbol G msnual Figures A to C, make no distinction between the power supply side primary circuit and the motor side secondary circuit. Using this adapter greatly Speed monitor Select by E48 3: Megger test of main circuit Use a VDC Megger and shut off the main power supply without fail during measurement.

Page 60 y codes: