E3C-VS1G OMRON PDF

Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Zujinn Nara
Country: Bulgaria
Language: English (Spanish)
Genre: Health and Food
Published (Last): 24 September 2008
Pages: 65
PDF File Size: 12.63 Mb
ePub File Size: 4.26 Mb
ISBN: 153-6-93649-777-4
Downloads: 33205
Price: Free* [*Free Regsitration Required]
Uploader: Nikojora

Separation from High Voltage Wiring Method Do not lay the cables for the Sensor together with high-voltage lines or power lines. This information by itself is not suf? This catalog is protected by copyright and is intended solely for use in conjunction with the product. Typical examples include the minimum sensing object, engineering data, step height detection data, and selection list for specifications.

Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Otherwise, it may malfunction or fail.

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output

Hold the connector cover to connect or disconnect the connector. Lens and Case The lens and case of the Photoelectric Sensor are primarily made of plastic. If Sensors are mounted in opposite each other, slant the Sensors as shown in the following diagram. Cable diameter Less than 4 mm 4 mm or greater Tensile strength 30 N max.

Doing so may result in damage from burning and fire, particularly if the liquid is flammable. AC Two-wire Sensors Example: If the Sensor does not operate, check the following points. Typical omrln are as given in the following table.

TOP Related  IEC 60243-2 PDF

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output Buy from Cross

Secure the connector cover by hand. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out the fibers. Any exceptions to this rule are indicated in Safety Precautions in individual product information. Although the bending repetition tolerance of a standard cable is approximately 13, times, robot cable has an excellent bending tolerance of approximatelytimes.

Keep organic solvents away from the Sensor. Insert a capacitor e.

Dirt should be gently wiped off with a dry cloth. Lowering the sensitivity will generally help. Cable Tensile Strength When wiring the cable, do not subject the cable to a tension greater than that indicated in the following table. Please know and observe all prohibitions of use applicable to the products.

Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch

In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability omfon asserted. The following measures can be taken to avoid mutual interference.

However, if the workpieces are close to the Photoelectric Sensors, light from the adjacent Emitter may be received and cause the Sensor to change to the incident light state. The axis perpendicular to the center of the lens. Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.

The Reflector cannot be mounted if there is any oil or dirt remaining. To maintain the fiber characteristics, make sure that the lock is released before removing the omronn.

The lens, however, is plastic. If the connector is not connected securely, the connector may be disconnected by vibration or the proper degree of protection of the Sensor may not be maintained. Radiant noise E3c-vs1t of high-frequency electromagnetic waves directly omorn Sensor, from power line, etc. Be sure to read Safety Precautions on page 4.

TOP Related  ELEMENTS OF ML PROGRAMMING ML97 EDITION 2ND EDITION PDF

They are rather values from samples taken from production lots, and are provided for reference as guidelines. Do not use thinner or other organic solvents. M8 and M12 Connectors? E3c-vss1g to the values in the above table to check bend-resistant performance under actual working conditions. Power line Work Required for Unconnected Leads Unused leads for self-diagnosis outputs or other special functions should be cut and wrapped with insulating tape to prevent contact with other terminals.

Precautions for Safe Use To ensure safety, always observe the following precautions. EE11 Check the parallel movement distance range in the catalog, verify the set distance between adjacent Sensors, and install the Sensors accordingly at a distance at least 1. Please notify us before copying or reproducing this catalog in any manner, for any other purpose. Insert a capacitor, etc.

These Sensors are designed for use in applications for sensing workpieces and workers that do not affect safety. Separate Sensors to distance where interference does not occur. As a general rule, wire the Sensor in a omrin system, use an independent metal conduit, or use shielded cable.

If copying or transmitting this catalog to another, please copy or transmit it in its entirety.